background image

OM 914257-0314-A

Congratulations

You have purchased the finest winch available in its service class.  It features a highly efficient 3 stage planetary 
gear set which transmits torque from a permanent magnet motor. A safe positive clutch allows free spooling for 
quick cable deployment. Your Ramsey winch was designed and manufactured to provide you with the utmost in 
utility. As with any device that combines power and movement in its use, there are dangers if improperly used.

At the same time, there are easier and faster ways for getting the job done if certain precautions are taken first. 
Please read this manual carefully. It contains useful ideas in obtaining the most efficient operation from your 
Ramsey Winch and safety procedures you need to know before beginning use. When you follow our guide-
lines for operation, your Ramsey winch will give you many years of satisfying service. Thank you for choosing 
Ramsey. You will be glad you have one working for you

.

Please Note: 

Ramsey UTV 5000 winches are designed primarily for ATV/UTV use. This winch is not designed to be used in industrial 

applications (car haulers /carriers, wreckers, hoisting, etc.), and Ramsey does not warrant it to be suitable for such use. Ramsey makes 
a separate, complete line of winches for industrial/commercial use. Please contact the factory for further information.

CAUTION: R

EAD

 

AND

 

UNDERSTAND

 

THIS

 

MANUAL

 

BEFORE

 

INSTALLATION

 

AND

 

OPERATION

 

OF

 

WINCH

.  S

EE

 S

AFETY

 P

RECAUTIONS

.

Ramsey Winch Company

OWNER’S MANUAL

UTV HONCHO 5000 Winch

NOTE: Fairlead does not attach directly to winch.

1

2

3

4

5

6

(lbs)

5,000

4,200

3,600

3,200

2,800

2,600

(kg)

2,270

1,900

1,630

1,450

1,270

1,180

(

Ō

)

5

15

30

40

55

60

(m)

1.5

4.5

9

12.1

16.7

18.2

(lbs)

1,000

3,000

5,000

(kg)

454

1,363

2,272

(FPM)

39

31

8

6

(MPM)

12.1

9.7

2.6

2.1

(12V)

72.8

180

295

420

Layer of Cable

Rated Line Pull
Per Layer
Cumula

Ɵ

ve Cable

Capacity Per Layer*

NO

LOAD

Layer
Line Speed First
Layer
Amp Draw

Line Pull First 

*Depends on cable being  
  uniformly wound onto drum.

Summary of Contents for UTV HONCHO 5000















Reviews: