manualshive.com logo in svg

RAM Ram 1500 2012, Owner'S Manual, Page: 237 / 726

Share
Download
RAM Ram 1500 2012 Owner'S Manual Download Page 237

To move the cleat to any position on the rail, turn the nut
counterclockwise, approximately three turns. Then pull
out on the cleat and slide it to the detent nearest the
desired location. Make sure the cleat is seated in the
detent and tighten the nut.

To remove the cleats from the utility rail, remove the end
cap by pushing up on the locking tab, located on the
bottom of the end cap. Slide the cleat off the end of the
rail.

1 — Utility Rail Detent
2 — Cleat Retainer Nut
3 — Utility Rail Cleat

Utility Rail End Cap

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

235

Summary of Contents for Ram 1500 2012























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments