background image

7

Electrical System Technical Manual

The throttle (A) is on the left side of the 

handle bar control unit. The throttle 

can be used as soon as the peddling 

assistance has been switched on. The 

use of the throttle costs a lot of energy. 

This affects the range of the e-bike. 

With some models you throttle up by 

turning the throttle away from you, 

whereas with other models you have to 

turn the throttle towards you. Carefully 

test what is applicable to your e-bike.
When using the throttle for the first 

time, carefully try it out to get familiar 

with the power the throttle delivers.

The throttle offers 

extra support and 

can be used in the 

following ways:

•  Extra support when you walk beside the bicycle

For instance, when taking the bicycle out of a basement, the throttle can give you some extra support, so you do not have to 

push the bicycle up only with your own power.

•  Extra support when accelerating from standstill

You can use the throttle when accelerating from standstill. The throttle supports up to 3 km/hour without peddling. After this 

you will have to peddle yourself in order to get support.

•  Extra support when cycling

The throttle can give the peddling assistance an extra impulse while cycling. This can be useful when you want to pass 

someone or when you have to ride uphill. The impulse is felt strongest with a low peddling assistance level.

Throttle

3

A

Summary of Contents for Array
















Reviews: