background image

 

- 10 - 

 

Chapter 2 

 

Parameters 

 
 

This section contains the following information: 

—

  V.35 interface Specification 

—

  Optical Fiber Interface Specification 

—

 Accessory 

Cables 

—

 Characteristic 

 

V.35 Interface Specification 

Electrical characteristics:  complies with ITU-T V.35 
Connecter:   

HDB26 female connector, through an adapt cable to ISO2593 
connecter  

Working mode: 

DCE (could also connect other DCE by cross connected 
cable) 

Bit rate:   

 

 

 

In E1 framed mode, V.35 bandwidth is N*64Kbps (N=1~31) 

 

 

 

 

 

 

In E1 unframed mode, V.35 bandwidth is 2048Kbps 

 

Optical Fiber Interface Specification 

Bit rate:   

 

 

 

 

4Mbps 

Line 

code: 

    disturbed 

NRZ 

(Private) 

Fiber 

connecter: 

   SC 

Optical Interface 

Model 

Type 

Working 

wavelength 

nm 

Launch power 

dBmW 

Receiving 

sensitivity 

dBmW 

Receiving 

saturation 

dBmW 

Distance 

(Km) 

Optical loss 

dB/Km 

-M 

DSC 

1310 

-18 ~ -14 

-31 

-14 

0 ~ 2 

-S1 

DSC 

1310 

-15 ~ -8 

-31 

-8 

0 ~ 25 

0.5 

-S2 

DSC 

1310 

-5 ~ -0 

-35 

-3 

10 ~ 60 

0.5 

-S3 

DSC 

1550/DFB 

-5 ~ -0 

-35 

-3 

15 ~ 120 

0.25 

-SS13 

SC 

1310/1550 

-15 ~ -8 

-31 

-8 

0 ~ 25 

0.5 

-SS15 

SC 

1550/1310 

-11 ~ -5 

-31 

-5 

0 ~ 25 

0.5 

-SS23 

SC 

1310/1550 

-5 ~ 0 

-35 

-3 

10 ~ 60 

0.5 

-SS25 

SC 

1550/1310 

-5 ~ 0 

-35 

-3 

10 ~ 60 

0.5 

 

Accessory Cables 

When connect this series product with DTE equipments such as routers through HDB26 interface, please use 
CBL-V35-HDB26M/M34F cable provided by Raisecom (standard accessory) to work with DTE/routers cable. 
When the CBL-V35-HDB26M/M34F cable is not long enough, please order it from Raisecom. 

When connect this series product with other venders DTE equipments, the cross cable 
CBL-V35-HDB26M/M34M-X is necessary, and please order it from Raisecom (non standard accessory). The 
default length of this cable is 2 meters. 

Summary of Contents for RC852-30-FV35

























Reviews: