Raisecom ISCOM6820-GP Hardware Description Download Page 16

Page: 16 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

2 Components

Raisecom Proprietary and Confidential

Components

This chapter describes the appearances, dimensions, and technical specifications of
components of the ISCOM6820-GP, including the following sections:



Overview



Main control uplink card (MCUA)



Basic service card (GPSC)



Expansion service card (GP16)



Expansion service card (GE16)



AC power module (RPA1302-220D4805)



DC power module (RPD1302-48D4805)



Fan module (FANS380)

2.1 Overview

2.1.1 Classification

The ISCOM6820-GP is composed of the following 5 types of components:



Main control uplink card



Basic service card



Expansion service card



Power card



Fan module

Table 2-1 lists components of the ISCOM6820-GP.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands