Raisecom ISCOM6820-GP Hardware Description Download Page 17

Page: 17 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

2 Components

Raisecom Proprietary and Confidential

Table 2-1

Components of the ISCOM6820-GP

Component

Name

Description

Main control uplink
card

MCUA

Control, management, aggregation, and
switching card

Provide two 10GE uplink interfaces, 1
SNMP interface, and 1 Console interface
(RJ45).

Basic service card

GPSC

Provide 16 GPON subcards.

Expansion service
card

GP16

Provide 16 GPON subcards.

GE16

Provide 16 GE subcards.

Power card

RPD1302-48D4805

Dual DC inputs

Provide a -48 VDC interface for the
service frame.

RPA1302-220D4805

Single AC input

Provide a 110/220 VAC interface for the
service frame.

Fan module

FANS380

Fan module

2.1.2 Appearances

Appearance of main control uplink card

Figure 2-1 shows the appearance of the main control uplink card (MCUA).

Figure 2-1

Appearance of the MCUA

Appearance of basic service card

Figure 2-2 shows the appearance of the basic service card.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands