Raisecom ISCOM6820-GP Hardware Description Download Page 23

Page: 23 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

2 Components

Raisecom Proprietary and Confidential

LED

Status

Description

LINK/ACT (RJ45
electrical interface
integrated LED)

Green

Line working LED



Green: the interface is connected properly and no data is
being transmitted.



Blinking green: the interface is transmitting data.



Off: the interface is disconnected or connected
improperly.

SPEED

(RJ45 electrical
interface
integrated LED)

Yellow Electrical interface working rate LED



Yellow: the electrical interface is working at 1000
Mbit/s.



Off: the electrical interface is working at 100 Mbit/s

2.2.5 Technical specifications

Table 2-7 lists technical specifications of the MCUA card.

Table 2-7

Technical specifications of the MCUA card

Parameter

Description

Dimensions

141.25 mm (Width) × 222 mm (Depth) × 37.30 mm (Height)

Weight

0.4 kg

Power consumption < 11 W

2.3 Basic service card (GPSC)

2.3.1 Introduction

The GPSC is a GPON card of the ISCOM6820-GP, providing 16 GPON SFP interfaces.

2.3.2 Panel and slots

The GPSC card can be only inserted into slot 3 of the ISCOM6820-GP.

Figure 2-9 shows the panel of the GPSC card.

Figure 2-9

Panel of the GPSC card

2.3.3 Interfaces

There are 16 interfaces on the GPSC card.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands