background image

ENGLISH

 

RAIS ­ manual for Rais Q­Tee 

11

 

Installation

 

It is prohibited to carry out unauthorised alterations to the stove. 

There must be plenty of fresh air in the room where the stove is being installed, in 
order to ensure proper combustion. Note that any mechanical exhaust ventilation ­ 
e.g. an extraction hood ­ may reduce the air supply. Any air grilles must be placed 
in such a manner, that the air supply is not blocked. 

Building Regulations Approved Document J gives specific guidance on the required 
permanent ventilation into the room for combustion air of solid fuel appliances. 

The floor structure must be able to carry the weight of the wood burning stove, as 
well as the weight of a chimney, if necessary. 

When you choose where to set up your RAIS wood burning stove, you should 
consider the heat distribution to the other rooms. This will enable you to get the best 
use out of your stove. 

The stove should be set up at a safe distance from inflammable materials. 

See the manufacturer's plate on the wood burning stove.

 

Commissioning and handover

 

Ensure loose parts are fitted in accordance with the instructions given in the 
instruction booklet. 

On completion of the installation allow a suitable period of time for any fire cement 
and mortar to dry out, when a small fire may be lit and checked to ensure the 
smoke and fumes are taken from the stove up the chimney and emitted safely to 
atmosphere. Do not run at full output for at least 24 hours. 

On completion of the installation and commissioning ensure that the operating 
instructions for the stove are left with the customer. Ensure to advise the customer 
on the correct use of the appliance with the fuels likely to be used on the stove and 
warn them to use only the recommended fuels for the stove. 

Advise the user what to do should smoke or fumes be emitted from the stove. The 
customer should be warned to use a fireguard to BS 8423:2002 (Replaces BS 
6539) in the presence of children, aged and/or infirm persons.

Summary of Contents for Q-TEE











































Reviews: