Rain Bird The Freedom System for Maxicom Instruction Manual Download Page 41

Page: 41 / 46

Appendix

Battery life and charging time

Battery life (90-5-5 duty cycle)

Model BPX-8N

BPX-8N-HC

BPX-8N-MH

Capacity

650 mAh

800 mAh

1100 mAh

Type

NiCad

NiMH

Five watts

Battery saver enabled

8 hrs.

9.8 hrs.

15.8 hrs.

Battery saver disabled

4.7 hrs.

5.8 hrs.

8.7 hrs.

90% duty cycle

7.2 hrs.

8.8 hrs.

14.2 hrs.

5% duty cycle

24 mins.

29 mins.

47 mins.

Two watts

Battery saver enabled

13.3 hrs.

16.4 hrs.

24.6 hrs.

Battery saver disabled

6.2 hrs.

7.6 hrs.

11.4 hrs.

90% duty cycle

12 hrs.

14.8 hrs.

22.1 hrs.

5% duty cycle

40 mins.

49 mins.

1.2 hrs.

Charging time

Model

BPX-8N

BPX-8N-HC

BPX-8N-MH

Capacity

650 mAh

800 mAh

1100 mAh

Type

NiCad

NiMH

Standard rate
charge time:

12-14 hrs.

16-18 hrs.*

20-24 hrs.*

Fast rate
charge time:

1.5 hrs.

*We strongly recommend the use of fast-rate chargers with these batteries.

Summary of Contents for The Freedom System for Maxicom











































Search results

Summary of Contents for The Freedom System for Maxicom

Reviews:

Related manuals for The Freedom System for Maxicom

Brands by name

Popular brands

Rain Bird The Freedom System for Maxicom, Instruction Manual

Search results

Summary of Contents for The Freedom System for Maxicom

Reviews:

Related manuals for The Freedom System for Maxicom

Brands by name

Popular brands