background image

Decoder Wiring Procedure - Secondary Path

Connect  the  two  (2)  white  decoder  wires  to  the 

1. 

two (2) solenoid coils of the valve-in-head rotor or 
remote control valve�
Record  the  decoder  address  and  following  the 

2. 

instructions in the PAR+ES Operation Manual, add 
the decoder address to the appropriate station at 
the controller�
Connect the two blue decoder wires to the wire 

3. 

path from the controller, one to the red wire and 
the other to the black wire�

Field Surge Protection for Decoders

LSP-1 surge arrestors are required for surge protection 
of decoders and solenoids� The LSP-1 surge arrestors 
consist  of  several  surge  arrestor  devices  potted  in  a 
cylindrical yellow plastic case� The LSP-1 has two blue 
wires and two green wires�

Install LSP-1s in the following locations:

Install LSP-1s so that there is no more than eight 

z

z

decoders between two LSP-1s or so that there is 
no more than 500 feet between LSPs, which ever 
is less�
Install LSP-1s at the last decoder in a dead end of 

z

z

a wire path�
Connect the two blue wires to the primary path 

1. 

wire, one to the black and one to the red wire�
Connect  the  green  wire  that  has  the  closed  eye 

2. 

spade  securely  to  the  core  tube  of  the  solenoid 
on the valve-in-head rotor or to a remote control 
valve by using a stainless steel nut threaded onto 
the core tube�
Connect  the  green  wire  to  a  ground  rod  on  a 

3. 

grounding grid using a brass clamp�

NOTE:

 

!

  A  resistance  of  50  ohms  or  less  is 

required  for  the  LSP-1  surge  arrestor  to  be 
effective�

If the decoder is not located next to the solenoid, 

4. 

install  the  LSP-1  near  the  decoder  and  connect 
both  green  wires  to  the  grounding  grid  using 
separate brass clamps�

PAR+ES Installation Manual

14

635778 Rev B (PAR+ES installation manual (1of2 ENG)) source.indd   14

9/2/2008   4:09:49 PM

Summary of Contents for PAR+ES

























Reviews: