Rail King UNION PACIFIC 4-6-2 49er Operating Instructions Manual Download Page 31

Page: 31 / 36

RailKing U.P. 49er Operating Manual

RAILKING

COUPLER PROBLEMS

REMEDY

The ProtoCoupler wont let the engine uncouple on

the Fly.

The power required to fire the coupler open when the

engine is on the Fly may be greater than the

ProtoSound system is capable of providing. As a

result, you may experience times when the coupler

wont fire open. Unfortunately, the only solution is to

stop the engine and fire the coupler in Neutral. If that

doesnt resolve the problem, try lubricating the coupler

knuckle and rivet as explained in the ProtoCoupler

Operation section.

I cant get the coupler to arm or fire open when I press

the whistle button.

You may be pressing the whistle button too quickly.

See the third remedy in the whistle section above.

Another possibility is that ProtoSounds has been

programmed to turn the coupler function off. See the

section entitled Using RESET to Program

ProtoSounds

Only one coupler will function when I press the whistle

button.

Only one coupler can operate at any one time. Use

the coupler selection switch on the bottom of the

chassis to choose which coupler you want active.

LOCKOUT PROBLEMS

REMEDY

I cant get the engine to run after I power up the

transformer. It sits still with the steam compressor

sounds running.

The engine is locked out into the Neutral position.

Follow the unlocking proceedures in the Lockout

Section.

The engine wont lock out into Forward, Neutral or

Reverse even after the short whistle blast sounds.

You are waiting too long to turn the throttle back on

after the short whistle blast sounds. The power must

be turned back on immediately after the short whistle

blast sounds or the engine will go back into RESET.

See the lockout proceedure in the Lockout Section.

VOLUME PROBLEMS

REMEDY

When I try to run the engine, the steam volume is OFF

or very low.

The steam volume has been programmed at a

reduced volume or to be silent. Go to RESET Feature

6 and adjust the volume. See the section entitled

Using RESET to Program ProtoSounds for more

information.

When I try to set the steam volume, it resets itself to

the original volume after I selected the new volume.

You are trying to set the volume with a poorly charged

or dead backup battery. See the section on Battery

Backup for more information.

When I try to set the Steam Volume to O Volume, I

still hear the neutral sounds.

When the steam volume is set to O, you will hear the

Neutral sounds because setting the steam volume only

controls the sound of the steam engine itself. All other

sounds, including neutral sounds, the whistle and bell

will continue to play at the volume level set by the

manual volume control knob located on the bottom of

the chassis. See the section entitled ProtoSound

Volume Adjustment for more information.

The sounds seem distorted, especially when the

whistle or bell is activated.

The overall ProtoSound volume has been set to high

creating the distorted sounds. Try turning the volume

control knob located on the bottom of the chassis

counter clockwise to reduce the overall volume level.

Summary of Contents for UNION PACIFIC 4-6-2 49er





































Search results

Summary of Contents for UNION PACIFIC 4-6-2 49er

Reviews:

Related manuals for UNION PACIFIC 4-6-2 49er

Brands by name

Popular brands

Rail King UNION PACIFIC 4-6-2 49er, Operating Instructions Manual

Search results

Summary of Contents for UNION PACIFIC 4-6-2 49er

Reviews:

Related manuals for UNION PACIFIC 4-6-2 49er

Brands by name

Popular brands