Raider RDI-ID39, User Manual

Page: 12 / 74

12 www.raider.bg
rotate the handle vspomagatelnata in the desired position. Then
tighten the grip again (8), such as turning it clockwise.
8.2. Setting the depth of drilling. With deep baffle) can be
pre-set depth of drilling. Pull the baffle so deep that the distance
along the axis between the tip of the drill and deep baffle is equal
to the desired depth of the hole.
8.3. Placing the drill in the chuck. Turn off the power of power.
Put the key in one of the open side of the chuck. Dissolving the
jaws to the desired size and place in the drill chuck. With key-
locking in three successive drill a hole in the chuck. We must
always remember that the key should be removed from the drill
after the completion of operations related to installation and
dismantling of the drill. When mounting a new drill should be
checked by the inclusion of a short drill, drill that rotates in an axis
without “flicker”. This will help us make sure that it is not distorted.
8.4. Inclusion and exclusion. Beware of the voltage of supply
network! Supply voltage of the network must conform to the
details shown on the plate of power. Appliances marked with 230
V, can be supplied with a voltage of 220 V.
8.5. To turn the drill press and hold the trigger switch (2).
For locking of the starting switch pressed (2) press (4). Exclusion
relax power trigger switch (2), respectively, if anchored to the
button (4), first press the short term and then release the trigger
switch (2).
8.6. Adjust the speed of rotation. Drill allows to work with
different speed of spindle. Alignment is done using the position
(3). In the range of each setting a speed can be adjusted smoothly
by increasing speed and reducing pressure on the trigger button
(2). Zavarteneto right speed regulator (3) leads to increase their
rotation and left to decrease.
8.7. Correct choice of the rate of speed shall be held where
drill is included without load. So speed-minded when working
with a load may be lower.
8.8. Hammer drilling.
Place the switch (5) the symbol “hammer drilling.” Switch (5)
falls in the correct position with a distinct twinge.
8.9. Tools to develop or cornering.
Turntable working instrument can be bent. After continuous
operation with low-speed power to cool as to leave it idling for
approximately 3 minutes with a maximum speed of rotation.
When working with terminals must always use a universal
extension. Use only the cores that are suitable for heads of
screws. Turning to always place the switch “drilling / hammer
drilling» (5) in position «Drilling».
8.10. Select the direction of rotation. With the switch (2) you
can change the direction of rotation of power. Rotate right: For
drilling and turning the screw press to switch the direction of
rotation (2) at point blank range left. Rotate left: To develop the
screws and nuts, press switch direction of rotation (2) right to the
point blank range. Switch (5) the choice of operation should be
in position «Drilling». It must be done to change the direction of
rotation when the spindle rotates a drill!
8.11. Not used in rotation to the left mode of attack.
8.12. When you need to vent large diameter, is recommended
first to break a small opening, which will then be drilling to the
desired size. This will prevent overloading the drill. Drilling deep
holes should be done gradually, as periodically removed from the
drill hole to remove chips or dust. If during drilling to drill holes
in zaklini, you should exclude drill. Use a change of direction
of rotation to remove the drill from the hole. Drill must be kept
in alignment with the hole. Ideally, the drill should be placed
perpendicular to the surface of the material being processed. If
the condition for perpendicularity is not respected at work can
lead to trapped or breakage in drill hole and injury to the user.
Continued drilling at low speed the engine from overheating
threatens. Must make periodic breaks during work or to allow the
drill to work on no-load maximum speed for about 3 minutes. Do
not obscure the openings in the hull used for ventilation of the
engine.
8.13. Outdoor use.
Switch the machine only in installations equipped with
electric switch “Fi” RCD (Residual Current Device). RCD must be
no more than 30 mA. Use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
Make periodic breaks at work.
Keep and refer to the accessories carefully.
Do not throw the tool, do not overload, do not soak in water
and other liquids do not use it for mixing adhesives and concrete
coatings.
9. Service and support.
9.1. Impact drill does not require additional lubrication or
special maintenance. There are no parts requiring maintenance
by the user. Never use water or any liquid chemical cleaning drill.
It should only be wiped with a piece of dry tissue. Should always
be stored in a dry place and ventilation holes in the body of the
drill to be free.
9.2. Replacing carbon brushes.
Exports (shorter than 5 mm), up or broken engine carbon
brushes should be replaced. Always replace both brushes
simultaneously. Work on replacement of carbon brushes
entrusted only to qualified person with original spare parts in
service of business RAIDER.
9.3. The repair of your power is best carried out only by
qualified specialists in workshops RAIDER, which used only
original spare parts. Thus ensuring their safe operation.
10. Environmental protection.
In view of environmental power, additional accessories and
packaging must be subjected to appropriate processing for reuse
of the information contained in these materials.
Do not dispose of household waste power! Under the EU