manualshive.com logo in svg

Radwin 5000, Configuration Manual

Share
Download
Radwin 5000 Configuration Manual Download Page 55

RADWIN

 

5000

 

Configuration

 

Guide

Release

 

4.9.17

3

‐

9

Activating

 

an

 

HBS

Installing

 

a

 

Sector

The

 

default

 

frequency

 

is

 

the

 

lowest

 

available

 

(5.735

 

GHz)

 

in

 

the

 

operating

 

band,

 

here,

 

5.730

 ‐ 

5.845

 

GHz

 

FCC/IC.

 

8. Click

 

Other

 

to

 

see

 

other

 

available

 

bands

 

for

 

this

 

HBS.

9. For

 

our

 

purposes,

 

we

 

choose

 

5.820

 

GHz:

right

 

hand

 

selector

 

wheel

Observe

 

that

 

the

 

right

 

hand

 

spin

‐

wheel

 

 

is

 

no

 

longer

 

displayed.

 

Had

 

you

 

left

 

Other

 

enabled,

 

you

 

could

 

have

 

chosen

 

a

 

frequency

 

by

 

working

 

through

 

those

 

available

 

in

 

5MHz

 

increments.

10. Choose

 

the

 

required

 

Channel

 

Bandwidth:

Summary of Contents for 5000





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands