background image

Page 22 of 22

IN052   Rev. K   0613

LIMITED WARRANTY

Subject to applicable consumer protection legislation, RadonAway warrants that the AIRaider

 will be free 

from defective materials and workmanship for the period of two (2) years from the date of purchase. 

Warranty is contingent on installation in accordance with the instructions provided. This warranty does 

not apply where repairs or alterations have been made or attempted by others; or the unit has been abused 

or misused. Warranty does not include damage in shipment unless the damage is due to the negligence 

of RadonAway. To make a claim under these limited warranties, you must return the defective item to 

RadonAway. All other warranties, expressed or written are not valid. RadonAway is not responsible for 

installation or removal cost associated with this warranty. In no case is RadonAway liable beyond repair or 

replacement of the defective product FOB RadonAway.

RADONAWAY SPECIFICALLY DISCLAIMS ANY WARRANTY OF FITNESS FOR A              

PARTICULAR PURPOSE.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION 

ON THE FACE HEREOF. THERE IS NO WARRANTY OF MERCHANTABILITY. ALL 

OTHER WARRANTIES,  EXPRESSED OR WRITTEN, ARE NOT VALID.

In order to obtain service under this warranty, the consumer must contact the installer or dealer where 

the unit was purchased. The installer or dealer must then contact RadonAway directly for a Return 

Merchandise Authorization  (RMA)  number  and  shipping  information.  No  returns  can  be  accepted 

without an RMA. RadonAway may require the defective part(s) to be returned to place of manufacture 

(freight pre-paid) to process the warranty claim. Defective part(s) covered under this warranty will be 

replaced or repaired at the place of manufacture and returned to the installer or dealer (freight pre-

paid). In replacing or repairing parts or products, RadonAway reserves the right to make such changes 

in the details of design construction, arrangement or make materials as shall in its judgment constitute 

an improvement over former practice.

Record the following for your records:

Serial No. 

    

Date Purchased:                                                          

3 Saber Way

P.O. Box 8244

Ward Hill, MA 01835

Phone: (800) 767-3703

Fax: (978) 521-3964

E-mail: [email protected]

Summary of Contents for AIRaider EZ95























Reviews: