RadioLink RC6GS V3 Instruction Manual Download Page 12 | Manualshive

Page: 12 / 40

background image

RadioLink Electronic Ltd

www.radiolink.com

11

When you power on the transmitter, LCD screen shows Model Name, Transmitter Name, Transmitter Voltage,
Steering Trim, Throttle Trim, Model Voltage, Subsidiary Model ID, Returned Signal.

Note

The Subsidiary ID won’t display until the function is activated in the menu ID SEED.

The telemetry function of model battery voltage can only be realized with R8FG/R7FG/R8F.

Model Name

The system can store the data for 30 models, model name will show on the LCD when you power on the
transmitter. Please make sure the model name is the right one that you want.
If the model name you chose is not corresponding with your model, the settings will be wrong.

Transmitter Voltage

In addition to the model, LCD can show the voltage of transmitter battery. Users can set transmitter low
voltage alarm in the basic menu -- ALARM. Low voltage alarm of the transmitter is 7.2V by factory default.It
can be customized on 2-4S battery. When the voltage reaches the alarm value, there will be a text displayed
on the transmitter screen and a "didi" sound dual alarm prompt to remind you.

Transmitter Function Menu Setting

When you want to browse or change a setting of transmitter, you should go into function menu setting mode.
Under function menu setting mode, you can set up Language "LANGUAGE" , Model Select "MODEL", End
Point Adjust "EPA", Steering Exponential "STEXP", Steering Speed "STSPD", Throttle Exponential "THEXP",
Throttle Speed "THSPD", A.B.S. Function "A.B.S", Throttle Acceleration "ACCEL", Idle-Up "IDLUP", Sub-trim
"SUB-TRIM", Channel Reverse "REVERSE", Steering/Throttle Dual Rate "D/R", Brake Side Adjustment
"ATL", Programmable Mixes "PMIX01/02", Auxiliary Channel 3, 4, 5 , 6 and 7 "AUX-CH"

，

Model name

"NAME", Low Voltage “ALARM”. Gyro Sensitivity”GYRO”, Fail Safe”F/S”, Subsidiary ID”ID SEED”, DSC port
setting "DSC", Timer setting "TIMER", Factory Reset "RESET".

Below menu introduction is based on this firmware V6.8.0 now. Menus may be various if the firmware
version is different. The latest firmware can be downloaded from

https://www.radiolink.com/rc6gsv3_firmware

«
...
10
11
12
13
14
...
»

Summary of Contents for RC6GS V3









































Reviews:

No comments

Related manuals for RC6GS V3

Brand: KELCO Pages: 36

Brand: Panasonic Pages: 16

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 20

Brand: Easy-Laser Pages: 84

Brand: Easy Heat Pages: 4

FT-2000 - MENU MODE LIST

Brand: Yaesu Pages: 56

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Real Living iM1

Brand: Yale Pages: 2

Brand: ACL Pages: 20

Brand: Acuity Controls Pages: 5

Brand: Risco Pages: 232

CompleteStat-Series CS9B-THO

Brand: Bard Pages: 2

Turbo-V 250 series

Brand: Varian Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands