manualshive.com logo in svg

RadioLink Mini Pix, User Manual

Share
Download
RadioLink Mini Pix User Manual Download Page 53

 

53 

 

world but these wide limits mean it’s more likely the 

compass calibration has not calculated good 

offsets and should be repeated. 

Compasses inconsistent

: the internal and external compasses are pointing in different directions 

(off by >45 degrees). This is normally caused by the external compasses orientation (i.e. 
COMPASS_ORIENT parameter) being set incorrectly. 

 

GPS related failures: 

GPS Glitch

 : the GPS is glitching and the vehicle is in a flight mode that requires GPS (i.e. Loiter, 

PosHold, etc) and/or the circular fence is enabled. 

Need 3D Fix

 : the GPS does not have a 3D fix and the vehicle is in a flight mode that requires the 

GPS and/or the circular fence is enabled. 

Bad Velocity

: the vehicle’s velocity (according

 to inertial navigation system) is above 50cm/s. 

Issues that could lead to this include the vehicle actually moving or being dropped, bad 
accelerometer calibration, GPS updating at below the expected 5hz. 

High GPS HDOP

 

: the GPS’s HDOP value (a measure of 

the position accuracy) is above 2.0 and the 

vehicle is in a flight mode that requires GPS and/or the circular fence is enabled. This may be 
resolved by simply waiting a few minutes, moving to a location with a better view of the sky or 
checking sources of GPS interference (i.e. FPV equipment) are moved further from the GPS. 
Alternatively, the check can be relaxed by increasing the GPS_HDOP_GOOD parameter to 2.2 or 2.5. 
Worst case the pilot may disable the fence and take-off in a mode that does not require the GPS (i.e. 
Stabilize, AltHold) and switch into Loiter after arming but this is not recommended. 

Note: the GPS HDOP can be readily viewed through the Missio

n Planner’s Quick tab as shown 

below. 
 

INS checks (i.e. Accelerometer and Gyro checks):  

INS not calibrated

: some or all of the accelerometer’s offsets are zero. The 

accelerometers need to 

be calibrated. 

Accels not healthy

: one of the accelerometers is reporting it is not healthy which could be a 

hardware issue. This can also occur immediately after a firmware update before the board has been 
restarted. 

Accels inconsistent

: the accelerometers are reporting accelerations which are different by at least 

1m/s/s. The accelerometers need to be re-calibrated or there is a hardware issue. 

Gyros not healthy

: one of the gyroscopes is reporting it is unhealthy which is likely a hardware issue. 

This can also occur immediately after a firmware update before the board has been restarted. 

Gyro cal failed

: the gyro calibration failed to capture offsets. This is most often caused by the 

vehicle being moved during the gyro calibration (when red and blue lights are flashing) in which 

Summary of Contents for Mini Pix


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands