background image

22

Searching

23

Searching

Searching

Use the search function to find active frequencies.

While doing a chain, fine tune, or service bank search, press 

•/DELAY

 to turn 

the delay on or off.

While doing a chain, fine tune, or service bank search, set the scanner to skip 
data signals (such as fax or modem signals) if you want to search only for 
audio (voice) signals (see 

“Skipping Data Signals” 

on p. 35).

Chain Search

This feature lets you search through preset frequency ranges. You can also 
program a range. There are three modes within this feature: Chain Search 
Mode, Chain Search Pause Mode, and Program Band Select Mode.

The preset frequency ranges are:

Bank

Frequency (MHz)

Step (kHz)

0

25.0000-54.0000

5

1

137.0000-174.0000

5

2

179.750-215.750

6000

3

216.0000-224.9950

5

4

225.0000-399.9875

12.5

5

400.0000-512.0000

6.25

6

764.0000-775.9875

12.5

7

794.0000-805.9875

12.5

8

806.0000-956.0000

12.5

9

1240.0000-1300.0000

12.5

Starting Chain Search

1.

Press 

SRCH

, and then repeatedly press 

SRCH

 until 

SR6

 appears at the 

top of the display.

2.

Press 

0 – 9

 to enable or disable the search bank being searched.

Note: 

At least one bank needs to be entered.

3.

Press 

T

 to search down or 

S

 to search up.

4.

When the scanner stops on a transmission, quickly press 

PSE

 to stop 

searching and listen to the transmission. 

SR6 PAUSE

 appears. To step 

through the frequencies during search Pause Mode, press 

T

 or 

S

.

5.

To release the hold and continue searching, press 

PSE

.

Storing Frequencies Found During a Search

To store frequencies you find in a search.

1.

Press 

FUNC + ENT/PGM

 when you find a frequency. 

2.

Press 

T

 or 

S

 to select a bank.

3.

Press 

ENT/PGM.

 The frequency you want to store, the smallest empty 

channel number, and 

“0.0000”

 are displayed.

4.

Press 

ENT/PGM

 to enter the frequency. After programming, 

“Edit Ch

Memory?”

 appears. Press  

ENT/PGM

 to go to Programming Mode, or 

press 

CL

 to go back to a previous mode.

Programming Search Ranges

To define the search range for each search bank during a chain search: 

1.

From Manual Mode, press 

ENT/PGM

 to put the scanner in Programming 

Mode.

2.

Press 

SRCH

 to go to Programming Search Bank Mode.

3.

Press 

T

 or 

S

 to select the bank number. Press 

ENT/PGM

.

4.

Using the number keys and 

, enter the lower limit frequency, and then 

press 

ENT/PGM

.

5.

Using the number keys and 

, enter the upper limit frequency, and then 

press 

ENT/PGM

.

6.

Press 

MAN

/

MENU 

to exit Programming Mode, or press 

CL

 to go back to a 

previous menu.

Summary of Contents for PRO-160










































Reviews: