background image

 
Chronosette-276  (120-1584)      Specifications        Faxback Doc. # 3772 
 
RADIO 
 
Frequency Range.............................................FM: 88-108 MHz 
                                                          AM: 530-1710 MHz 
 
CASSETTE PLAYER 
 
Tape Speed.......................................................1 7/8 ips 
Erasing System..............................................Magnetic Erase 
Recording System...................................................AC Bias 
 
GENERAL 
 
Power Output.........................................................700mW 
Speaker..................................................3 1/2 Inch, 8 Ohm 
                                                    Permanent Dynamic Type 
Dimensions...........................13 5/8 x 4 1/3 x 5 11/16 Inches (HWD) 
Weight...............................................................4 lbs 
Power Requirements.................................AC: 120 volts 60Hz, 10W 
                        220/240 volts 50 Hz for European/Australian Models 
Room temperature...............................77 degrees F (25 degrees C) 
 
AM BAND 
 
Speaker impedance:..................................................8 ohms 
 
Output readings are taken across a non-reactive load. 
 
Output reference level is 50mW total power. 
 
The generator output shall terminate in an IRE loop with the loop pointing 
toward rear of receiver. 
 
Modulation:...................................................1000 Hz, 30% 
 
                                UNIT            NOMINAL              LIMIT 
 
Frequency Coverage              kHz             510-1750           520-172 
IF                              kHz             455                   +/-3 
 
Antenna Sensitivity 
for S/N 20 dB       at 600 kHz  microV/M        500                    900 
                    at 1000 kHz microV/M        500                    900 

Summary of Contents for Chronosette-276

















Reviews: