background image

7

Preparation

Note: You can place the handset on the base faceup or facedown.

Recharge the battery pack when: the LOW BATT indicator on the handset 
flashes, the phone beeps four times when you press 

PHONE

, the LOW 

BATT indicator is on when the phone is off, or the phone does not operate 
when you press 

PHONE

Notes:

²

When you first use the phone after charging or recharging the battery pack, the phone might not work and 

you might hear a two-beep signal when you press 

TALK

. If this happens, return the handset to the base for 

about 15 seconds. This resets the security access protection code.

²

If the CHARGING indicator does not light when you place the handset on the base, be sure the battery pack 

and AC adapter are correctly and securely connected. 

Also, check the charging contacts on the handset and the base. If the 

contacts are dirty or tarnished, clean them with a pencil eraser.

²

If the battery pack gets completely discharged or the base loses power while the handset is away from it, 

the security access-protection code needs to be reset. To reset the code, place the handset on the base for 
about 15 seconds. If it was the handset that lost power, leave the handset on the base to charge the battery 
pack.

²

If the battery pack gets weak during a call, the handset sounds 4 beeps every 30 seconds. If this happens, 

you cannot make another call on the phone until you recharge the battery pack.

²

About once a month, fully discharge the battery pack by keeping the handset off the base until the LOW 

BATT indicator lights. Otherwise, the battery pack loses its ability to fully recharge.

²

If you are not going to use your phone for an extended period of time, disconnect the battery pack. This 

increases the battery pack’s usable life.

²

The supplied battery pack should last for about a year. When it loses its ability to fully recharge, order a 

replacement battery pack from your local RadioShack store (see “Replacing the Handset battery pack” on 
Page 24).

Preparation

SETTING THE DIALING MODE

Set the dialing mode for the type of service you have. If you are not sure which type you have, once the battery 
pack is fully charged, do this test.

LOW BATT
Indicator

Illustration of handset

Charging
Contacts

Charging
Contacts

Illustration of charging
contacts on handset and bas

Summary of Contents for 43-5515





























Reviews: