(Rear Cover)
Functions
Room Temperature
Suitable ambient temperature is important for the baby and patient, the thermometer always help you recognize the
room temperature.
When in power off, room temperature will always be shown on the screen with icon.
Please see the “Use of the thermometer” section to learn how to get the correct room temperature.
Forehead
Temperature
The thermometer has been designed for home use. It’s not meant to replace a visit to the doctor. Please also remember
to compare the measurement result to your regular body temperature.
Please see the “Use of the thermometer” section to learn how to measure the body temperature.
Scan Mode
The Scan mode shows the actual, unadjusted surface temperatures, which is different from the body temperature. It can
help you to monitor if the object temperature is suitable for the baby or patient, for example the baby’s milk.
Please see the “Use of the thermometer” section to to learn how to measure the object temperature.
Fever Indication
If thermometer detects a body temperature
≥
37.5°C under forehead mode, there will be a long beep sound followed by
three short beep sound to warn the user for potential fever.
Last Reading
When you get a new temperature reading in forehead mode, the last reading will be shown on the screen (at top right
corner) with the
icon.
Memory Locations
There are total 25 sets memories for body temperature.
When in power on, press the “ON/MEM” button to see the temperature stored with
icon.
°C / °F Switch
In “power off” mode (The LCD only shows the room temperature). Press and hold the “SCAN” button, then
immediately press and release the “ON/MEM” button. After 3 seconds, icon “°C” will be switched to icon “°F”. (You may
use the same way to switch back to “°C”)
Use of the thermometer
Note: If there is any temperature difference between the places where the device is stored and where you are going to
measure, subject and the device should stay in the same room for at least 15 minutes before measurement.
1. Always make sure the probe is clean, and without damage.
2. Power on: Press “ON/MEM” button.(see figure 1)
3. Mode selection:
3.1
Forehead mode
: Press the “ON/MEM” button, the default mode of thermometer is forehead mode. The thermometer is
ready for use after you see the icon on the screen and hear two beep sounds (see figure 1). In
this mode, you can get the body temperature by forehead measurement.
3.2 Scan Mode
:
After power on, press and hold the “ON/MEM” button, and press the “SCAN” button
one time for “Infrared thermometer” mode
to see
icon on your LCD display (see figure2).
In this mode, you can get the target surface temperature.
4. Temperature taking:
4.1 Forehead temperature measuring, points for attention:
Remarks: a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its “oral-equivalent” Value.
b. Before the measurement, the subject should stay in a stable environment for 5mins and avoid exercise, bath for 30mins.
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
d. The “Clinical Bias” is -1.3 ~ -1.5°C.
e. The “Limits of Agreement” is 0.31.
f. The "Repeatability" is 0.17°C.
TH60F Non-contact Forehead Thermometer
Intended use: The non-contact forehead thermometer is electronic thermometer using an infrared detector
(thermopile detector) to detect body temperature from forehead center in people of all ages.
Intended operator: Have eight years of education, no maximum.
Specifications
Temperature measurement range:
Forehead mode: 34~42.2°C (93.2~108°F), Surface mode: -22~80°C (-7.6~176°F)
Operating temperature range: 10~40°C (50~104°F), 15%~85% RH
Storage temperature range: It should be stored at room temperature between -20~+50°C, RH
≤
85%
Transportation temperature shall be less than 70°C, RH
≤
95%
Atmospheric pressure: 800~1013 hPa
Comply with ASTM E1965-98, EN ISO 80601-2-56, IEC/EN60601-1-2(EMC), IEC/EN60601-1(Safety)
standards, ISO10993, RoHS
Accuracy:
For forehead mode:
±0.2°C (0.4°F) within 35~42°C (95~107.6°F), ±0.3°C (0.5°F) for other range.
For surface mode:
±
0.3°C (0.5°F) within 22~42.2°C (71.6~108°F), others
±
4% or
±
2°C (4°F)
whichever is greater.
Fever indication & Temperature records under “Forehead mode”
°C / °F Switch mode
Battery: one lithium cell battery (CR2032 *1pcs)
This thermometer is an adjusted mode thermometer that converts the forehead temperature to
display its “oral equivalent.” (according to the result of the clinical evaluation to get the offset value)
Enclosure Rating: IP22
Dimensions: 104.4 x 68.9 x 28.1 mm
Weight: 57.4 grams including battery
Battery life: around 3,000 continuous readings.
Expected Service Life: 4 years
The device should not submerge into any liquids and expose it to direct moisture.
There is no gender and age limitation for using infrared thermometer.
This is not an AP
or APG product.
Figure 1 Figure2
