background image

 
 
                                                                                       

Radiant Innovation 

9

 

 

Install the battery cover 

 
Then follow the counter clockwise direction to lock the battery corer.  You will hear 
the voice of “Kok” when the battery cover is correctly locked. 
 

 
                         
 
 
 
 
 

ß

 The two bumps of the battery cover will line up with the 

hole of the key ring at this moment. 

 
 

 Warning:   

The unit may be damaged when changing the battery under power on condition or 
the battery was installed with the incorrect direction. Try to switch off then on one 
more time if abnormal situation occurred.  If the situation is still, contact your 
local service center for support.

 

 
Battery may be damaged if mistreated. Do not recharge, disassemble or dispose 
into fire. Dispose of used battery promptly and keep away from children. 

 
 

Replace battery with the following battery types. Why restrict the brand? Use of another 
battery may present a risk of fire or explosion.   

 

 

SONY 

 

 

 

CR2032 

 

FUJI  

 

 

 

CR2032 

 

MATSUSHITA 

    CR2032 

 

RADIO SHACK 

 

CR2032 

 

RENATA  

 

 

CR2032 

 

VARTA   

 

 

CR2032 

 

AVEREADY/UCAR   CR2032 

REPLACE BATTERY

Summary of Contents for TempFairy TN1














Reviews: