Radial Engineering B-RAD X 7000 User Manual Download Page 13

CAUTION! 

The RAD HD Battery Pack should only be charged on the RAD Battery Charger. 
If an incompatible charger is used, damage to the RAD HD Battery will occur.

!

User manual 

B-RAD X

V1.0 - May 2023

13

2.4. RAD Battery Charger

The Charging Status Display (Figure 2.4-1) indicates 
when the RAD HD Battery is charging, when the 
charge is complete, and if there is an error.

2.4.1.  Charging the RAD HD Battery Pack

If the battery was discharged under heavy load, the charger may indicate a battery overtemperature (Solid 
red warning light). This is normal. Keep the battery on the charger while the battery cools. The charging 
process will start automatically after about 15 to 30 minutes.

Note: 

The temperature range for charging is 0˚C to 50˚C (32˚ F to 122˚ F). 

To charge the RAD HD Battery:

  1.  Plug the RAD Battery Charger into the wall outlet. The Red Warning Light will turn on for 
     one second and then the Green Status Light will turn on for one second.
  2.  Align the RAD HD Battery with the RAD Battery Charger.
  3.  Slide the RAD HD Battery into place. The Green Status Light will fl ash while the RAD HD 
     Battery is charging.
When the RAD HD Battery has been fully charged, the Green Status Light will stop fl ashing and stay 
illuminated. Until the RAD HD Battery is removed from the RAD Battery Charger, the Charger will maintain 
the battery charge at maximum capacity.

To remove the RAD HD Battery:

  1.  Slide the RAD HD Battery away from the RAD Battery Charger.
  2.  Check that the RAD HD Battery is fully charged 
     (refer to Section 2.4 RAD HD Battery Charge).

2.4.2. Charging Errors

The Red Warning Light is on:

The RAD HD Battery is not charging because its temperature is not within the required temperature range 
for charging. When the RAD HD Battery’s temperature changes to within the required range, the Red 
Warning Light will turn off  and charging will start.

The Red Warning Light is flashing:

The RAD HD Battery may be placed incorrectly on the RAD Battery Charger. Remove the RAD HD Battery 
and replace it correctly on the RAD Battery Charger. If the Red Warning Light continues to fl ash, the RAD 
HD Battery is defective; remove the RAD HD Battery immediately. 
If these problems continue, contact Radial Torque Tools B.V. Technical Support (refer to Section 6. Contact 
Us) or your RAD Distributor.

Green Status Light

Red Warning Light

Figure 2.4-1: Charging Status Display

Summary of Contents for B-RAD X 7000





























Reviews: