manualshive.com logo in svg

RACOM RAy3-11, User Manual, Page: 48 / 241

Share
Download
RACOM RAy3-11 User Manual Download Page 48

3.2.6. WiFi settings

Menu Link > Service access > USB accessories

Go to menu Link Settings > Service Access > USB accessories and enter WiFi password or disable
WiFi completely. Standard settings are that Enable on Air link loss is ON (when the link is down, WiFi
is activated; when link is OK, WiFi will be deactivated in few minutes) and Force Enable is OFF (activates
WiFi permanently). Passphrase has to be set, otherwise the WiFi is unsecured and system warning is
active.

Fig. 3.7: Configuration menu Link settings > Service access > USB accessories

Note

If you access the unit over WiFi, do this step as last action before reboot (as the WiFi connection
will be interrupted and new connection with new password would be required to continue the
work).

For full explanation of possibilities of this screen see

Section 5.4.3.2, “USB accessories”

in

Chapter 5,

Configuration

.

RAy3 Microwave Link – © RACOM s.r.o.

48

Step-by-step Guide

Summary of Contents for RAy3-11


















































































































































































































































Reviews:

No comments