background image

SLIM    37 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. 
Call the Marketing Department at 888-RAB-1000 or email: [email protected]

TM

SLIM35 POLYSHIELD

RAB LIGHTING

3/22/2013

SLIM35 WIRE GAURD

RAB LIGHTING

3/22/2013

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation 
or maintenance.

CLEANING & MAINTENANCE

CAUTION: Be sure fixture temperature is cool enough to 

touch. Do not clean or maintain while fixture is energized.

1.  Clean glass lens & fixture with non-abrasive glass cleaning 

solution. 

2.  Do not open fixture to clean the LED. Do not touch the LED.

TROUBLESHOOTING

 

1.  Check that the line voltage at fixture is correct. Refer to 

wiring directions.

2.  Is the fixture grounded properly?

3.  Be sure the photocell, if used, is functioning properly.

GUARD/ SHIELD INSTALLATION

1.  Remove left and right 

Cover Plates

 as in figure 1 and 

discard. 

2.  Mount wire guard and/ or poly shield with (4) #8-32 x 1/2” 

Stainless Steel Screws.

 Screws are provided with the 

accessory.

Stainless Steel Screws (4) 

FULL CUTOFF/ GUARD/ SHIELD 

INSTALLATION

1.  Remove (4) 

Stainless Steel Screws

 from the 

Full Cutoff 

Hood.

2.  Mount wire guard and/ or poly shield over the full cutoff 

hood with (4) #8-32 x 1/2” 

Stainless Steel Screws 

as shown 

in figure 2. Screws are provided with the accessory.

Stainless Steel 

Screws

Figure 1

Stainless Steel 

Screws

Figure 2

Cover Plate

Full Cutoff Hood

Note: Guard and shield may be used together. 

Note: Guard, shield and full cutoff hood may be used together 

with (4) #8-32 x 3/4” stainless steel screws (supplied by others).

Stainless Steel Screws (4) 

PHOTOCELL INSTALLATION

Photocell may be installed in the field. Apply weatherproof 

silicone sealant to all plugs and unused conduit entries.
1. Remove close up plug on top of the wall mounting box.
2. Install photocell and wire as per diagram.
3. Use photocell rated for your supply voltage.

“COM”

PHOTOCELL

WP2FC

LIGHT 

FIXTURE

BLACK

WHITE

PHOTOCELL

Summary of Contents for SLIM 37










Reviews: