background image

LOTBLASTER    65W 110W 160W INSTALLATION 

INSTRUCTIONS

Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. 
Call the Marketing Department at 888-RAB-1000 or email: [email protected]

  ™

MOUNTING UNIVERSAL POLE 

ADAPTER TO SQUARE POLE

Follow steps below to mount the 

Universal Pole Adaptor 

(UPA)

 to 

Square Pole (not supplied)

. Refer to Variable 

Bolster Plate Detail regarding drill hole spacing on pole.

1. 

Adjust 

Bracket

 on 

Variable Bolster Plate

 to desired bolt 

spacing and tighen 

Screw (2)

. Refer to Variable Bolster 

Plate Detail for more information. 

2. 

For 

Square Pole (not supplied)

, use 

Gasket for Round 

Pole

 along with 

Gasket for Square Pole.

3. 

Line up 

Universal Pole Adaptor (UPA)

Gasket for 

Round Pole

Gasket for Square Pole

, top hole on the 

Square Pole

 and top hole on 

Variable Bolster Plate

.

4. 

Feed supply wires from center opening of 

Square Pole

 

through gaskets and 

UPA

.

5. 

Thread 

3” Bolts (2)

 along with washers and lockwashers 

(supplied) through 

UPA 

and tightly secure to 

Variable 

Bolster Plate

.

6. 

Insert the 

Screw Cover. 

MOUNTING FIXTURE TO UNIVERSAL 

POLE ADAPTER

Follow steps below to mount the 

Housing

 to

 Universal 

Pole Adaptor (UPA) 

-

1. 

Tightly secure 

1-1/4” Bolts (2)

 to 

Housing

 from the 

outside as shown below, until they bottom out.

2. 

Feed supply wires from 

UPA

 to 

Housing

.

3. 

Slide fixture down onto 

UPA

. Make sure the fixture is held 

stable by the 

1-1/4” Bolts (2)

4. 

Loosen 

Cover Screws (2) 

to open the 

Housing

.

5. 

Be sure the gasket is between 

Housing 

and

 UPA. 

Insert 

and tighten 

1-3/4” Bolts (2) 

from inside of 

Housing 

into 

the 

Universal Pole Adapter. 

6. 

Make necessary connections inside the 

Housing

 and 

knot wires for strain relief.

7. 

Close 

Housing 

cover and tighten the 

Cover Screws (2)

.

8. 

Secure pole cap (not supplied). 

Variable

Bolster Plate

Gasket 

for Round 

Pole

3” Bolts (2)

Screw 

Cover

1-1/4” Bolts

          (2)

1-3/4” Bolts

          (2)

Universal 

Pole Adaptor 

(UPA)

Cover Screws

(2)

Square 

Pole (not 

supplied)

Universal 

Pole Adaptor 

Gasket for 

Square Pole

Bracket

Screw (2)

Housing

Summary of Contents for LOTBLASTER 65W






Reviews: