background image

36 / 38

User Manual

Rev. 1.0 - 29/06/09

PJ2500M-C, PJ3000HE, PJ3500M-C,  

PJ4000U-K & PJ5000U-K

This card also supplies the following measurements: current and voltage of each 

module, total current and average voltage.

  8.3.4  Low-Pass Filter

This filter is located at the back of the equipment.

The task of the low-pass filter is to reduce the harmonic emissions of the amplifier 

to below the levels allowed by standards.

  8.3.5  Directional Coupler

The task of these two cards that seem identical is to supply the power measurement. 

They are installed on the input RF connector on the inside of the machine. One 

card supplies the amplifier’s forward power whereas the other one supplies the 

reflected power.

  8.3.6  Control Board

The control board acts as an auxiliary card for the PROTF card in the PS section 

should the latter fail to trip due to a malfunction. It implements all the functions 

associated with measurements, protection, control and communications and is 

even capable of detecting the individual voltages or currents inside the machine, 

in addition to the overall ones.

If pre-arranged, this Board can carry the signals to the DB9 connector located on 

the machine’s back panel in RS485 standard.

  8.3.7  LEDs Board

This card is fitted with 4 warning LEDs that indicate the machine’s general operating 

status.

It also has a trimmer for adjusting power (AGC control). Use a small screwdriver 

to change the delivered power.

Summary of Contents for PJ2500M-C











































Reviews: