R-Tech I-CUT100P Operation Instructions Manual Download Page 7 | Manualshive

Page: 7 / 17

R-Tech I-CUT100P Operation Instructions Manual Download Page 7

Turn the input power OFF at the mains switch & fuse box before working on this equipment. Have a qualified
electrician install & service this equipment. Allow machine to sit for 5 minutes minimum to allow the power
capacitors to discharge before working inside this equipment. Do not touch electrically live parts

The PLASMA I-CUT 100P Plasma Cutters require a 415V 50/60Hz 3-Phase supply. It requires a 32A fuse. It
comes with a 3 metre mains cable attached. Connect wires according to national coding.

Brown, Black, Grey wires = Live
Green/Yellow Wire Earth (Ground)

Connecting to a mains electrical supply

THIS MACHINE IS OF AN INDUSTRIAL SPECIFICATION AND MUST BEFITTED

TO A 32AMP 415V MAINS INPUT - FAILURE TO RUN ON CORRECT SUPPLY

WILL IN-VALIDATE WARRANTY

Connecting to an Engine Driven Generator

If connecting this Plasma Cutter to an engine driven generator please ensure

the following

Minimum Generator KVA Output 15KVA continuous

Generator to be fitted with AVR (automatic voltage regulation)

DO NOT USE ON A GENERATOR WITHOUT AVR

Connecting to a generator without the above minimum requirements will

invalidate your warranty.

7

«
...
5
6
7
8
9
...
»

Summary of Contents for I-CUT100P


















Reviews:

No comments