background image

Page 4

06206-90(I)

EMC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation 

is subject to the following two conditions: (1) this device may not 

cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause 

undesired operation.

This equipment has been tested and found to comply with the 

limits for a Class A digital device, pursuant to part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection 

against harmful interference when the equipment is operated in a 

commercial environment. This equipment generates, uses, and 

can radiate radio frequency energy and, if not installed and used 

in accordance with the instruction manual, may cause harmful 

interference to radio communications.  Operation of this equipment 

in a residential area is likely to cause harmful interference in which 

case the user will be required to correct the interference at his own 

expense.

This ISM device complies with Canadian /CES-001.

Cet apparei/ISM est conforme a Ia norme NMB-001 du Canada.

EN55011/CISPR 11, Group 1, Class B device

Class B equipment is suitable for use in domestic establishments 

and in establishments directly connected to a low voltage power 

supply network which supplies buildings used for domestic 

purposes.

Note:

Instrument measurements may be disrupted by conducted 

 

RF interference at 13, 35, and 54 MHz.
To meet EMC Compliance, a ferrite core (YOUNG 18500) must be 

installed on the wall adapter DC power cable.  The cable must pass 

through the center hole of the choke at least 4 times, creating 3 

loops around the outside as shown below.

18500 FERRITE CHOKE

WARRANTY

This product is warranted to be free of defects in materials and 

construction for a period of 12 months from date of initial purchase. 

Liability is limited to repair or replacement of defective item. A copy 

of the warranty policy may be obtained from R. M. Young Company.

CE COMPLIANCE

This product has been tested and complies with European CE 

requirements for the EMC Directive. Please note that shielded cable 

must be used. 

Summary of Contents for 06206










Reviews: