Qvis IZEUS 7000 NVR RANGE User Manual Download Page 47

Page: 47 / 233

From

Main menu->Setting->System->Display

, you can see an interface shown in Figure 4-25.

Here you can set the tour parameter.



Enable tour:

Check the box here to enable tour function.



Interval:

Input proper interval value here. The value ranges from 1-120 seconds.



Monitor tour type

: System support 1/8-window tour.



Alarm tour type

: System support 1/8-window tour.

Figure 4-25

Tips

On the navigation bar, click

to enable/disable tour. Click Save button to save current

setup.

4.6 PTZ

Note:

Before you control the PTZ, please make sure the PTZ decoder and the NVR n etwork

connection is OK and the corresponding settings are right.

4.6.1 PTZ Settings

Cable Connection

Please follow the procedures below to go on cable connection:

1. Connect the dome RS485 port to NVR RS485 port.

2. Connect dome video output cable to NVR video input port.

3. Connect power adapter to the dome.

Summary of Contents for IZEUS 7000 NVR RANGE










































































































































































































































Search results

Summary of Contents for IZEUS 7000 NVR RANGE

Reviews:

Related manuals for IZEUS 7000 NVR RANGE

Brands by name

Popular brands

Qvis IZEUS 7000 NVR RANGE, User Manual

Search results

Summary of Contents for IZEUS 7000 NVR RANGE

Reviews:

Related manuals for IZEUS 7000 NVR RANGE

Brands by name

Popular brands