background image

 

© Copyright Qvis ®. All documentation rights reserved.   
 

184 

Parameter 

Function   

whole week. 

Click OK button, system goes back to local alarm 
interface, please click save button to exit. 

Anti-dither 

System only memorises one event during the anti-dither 
period. The value ranges from 5s to 600s. 

Sensor type   

There are two options: NO/NC. 

Record channel 

System auto activates motion detection channel(s) to 
record once an alarm occurs. Please note you need to set 
alarm record period and go to Storage-> Schedule to set 
current channel as schedule record. 

Record Delay   

System can delay the record for specified time after alarm 
ended. The value ranges from 10s to 300s. 

Alarm out 

Enable alarm activation function. You need to select alarm 
output port so that system can activate corresponding 
alarm device when an alarm occurs.     

Latch 

System can delay the alarm output for specified time after 
an alarm ended. The value ranges from 1s to 300s.   

Show message 

System can pop up a message to alarm you in the local 

host screen if you enabled this function. 

Buzzer   

Check the box here to enable this function. The buzzer 
beeps when an alarm occurs. 

Alarm upload   

System can upload the alarm signal to the centre 
(Including alarm centre). 

Send Email   

If you enabled this function, System can send out an email 
to alert you when an alarm occurs. 

Tour 

You need to click setup button to select tour channel. 
System begins 1-wiindow or multiple-window tour display 
among the channel(s) you set to record when an alarm 
occurs. See Figure 5-53. 

PTZ Activation   

Here you can set PTZ movement when alarm occurs. 
Such as go to preset X. See Figure 5-59. 

Snapshot   

Click setup button to select snapshot channel. See Figure 
5-54. 

 

5.8.3.2.2  Net Alarm 

The network alarm interface is shown as in Figure 5-60. 

 

Network  alarm  refers  to  the  alarm  signal  from  the  network.  System  does  not  anti-dither  and 

sensor type setup. For setup information, please refer to chapter 5.8.3.2.1. 

Summary of Contents for IZEUS 7000 NVR RANGE










































































































































































































































Reviews: