manualshive.com logo in svg

Quonset Microwave QM1004-0.5-18, User Manual, Page: 83 / 105

Share
Download
Quonset Microwave QM1004-0.5-18 User Manual Download Page 83

QM1004-0.5-18 Combined RF Upconverter/Downconverter

User Manual

5.8 SYSTem:SAVEstate [1-5]

This command saves the current setup to non-volatile memory. There are 5 re-writeable memory loca-
tions, specified by choosing an index between 1 and 5. Any of the 5 states can be restored on startup
when specified with the SYSTem:BOOTstate command. The parameters saved are the

RF Power State,

Reference Frequency, External LO1 Enabled, External LO1 Switch Override, External LO2 Enabled, Ex-
ternal LO2 Switch Override, External Reference Enabled, External Referece Switch Override, Tune Fre-
quency, Upconverter Bypass Enabled, Upconverter LNA Power State, Upconverter Attenuation 1, Up-
converter Attenuation 2, Upconverter ASR State, Downconverter Bypass Enabled, Downconverter LNA
Power State, and Downconverter Attenuation

. For a detailed description of the parameters saved, see

the relevent command descriptions in this manual. NOTE: The MEM_CLR button on the back panel will
rewrite the contents of states 1-5 with the contents of state 0 when depressed, serving as a reset to
factory defaults.

Syntax

:

SYST

:

SAVE

Space

1-5

?

There are 5 memory locations, numbered 1 through 5. Memory location 0 contains the factory default
settings and is write-protected.

Example

:SYST:SAVE 3

This command saves the current state to memory location 3

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 1 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.2.1

72

Summary of Contents for QM1004-0.5-18










































































































Reviews:

No comments