Quickie Life, Directions For Use Manual

Page: 14 / 64

ENGLISH
14
Quickie Life Rev.2.0
Brake Lever Extension
The longer lever helps to minimise
the effort needed to set the wheel
locks.
The brake lever extension is
screwed to the brakes. By raising
this, it can be flipped forward
(Fig. 6.3).
CAUTION !
Mounting the wheel lock too close
towards the wheel will result in a higher effort to operate. This
might cause the brake lever extension to break!
Leaning onto the brake lever extension while transferring will
cause the lever to break! Splashing water from tyres might
cause the wheel lock to malfunction.
CAUTION !
Incorrect mounting of the wheel
lock will result in a higher effort to
operate.
This might cause the wheel lock
extension lever to break.
Compact Brakes
Compact brakes are underneath
the seat sling and are operated by
pulling the brakes towards the rear,
in the direction of the tyre. For the
brakes to work properly, this must
be pulled until it reaches the stops, (Fig.6.4).
Fig. 6.3
Fig. 6.4
Drum Brakes
Drum brakes permit safe and convenient braking for an atten-
dant. They can also be set with the aid of a locking lever (1) to
prevent rolling. This lever must snap audibly into place. Drum
brakes do not independent on the aid of air pressure inside the
tires. Your wheelchair cannot be moved when the drum brakes
are set, (Fig.6.2).
Wheel Locks (Fig.6.0-6.1)
Your wheelchair is equipped with
two wheel locks. They are applied
directly against the tyres. To
engage, press both brake levers
forward against the stops. To
release the locks, pull the levers
back to their original positions.
One Hand Wheel Locks (Fig.6.1.1)
Your wheelchair is equipped with
two sets of wheel locks, that
operate from the left or the right
side. They are applied directly
against the tires. To engage, press
the wheel-lock lever forward against
the stop. To release the wheel, pull
the lever back to the original
position.
WARNING!
Braking power will decrease with:
Incorrect fitting and adjustment •
of the brakes.
Tyre pressure too low. •
Worn tyre tread •
Wet tyres •
Improperly adjusted wheel •
locks.
The wheel locks have not been •
designed to be used as brakes
for a moving wheelchair.
The wheel locks should therefore never be used to brake a •
moving wheelchair.
Always use the hand-rims for braking. •
Make sure that the gap between the tyres and wheel locks
complies with given specifications. To re-adjust, loosen the
screw and set the appropriate gap. Then re-tighten the screw
(Fig. 6.0, 6.1, 6.1.1).
After each adjustment of the rear wheels, check the wheel lock
gap and re-adjust if necessary.
Brakes
Fig.6.0
6.0 Options
1
Fig. 6.2
Fig. 6.1
3 mm
Fig. 6.1.1
3 mm
One Hand Wheel Locks
Your wheelchair is equipped with two sets of wheel locks, that
operate from the left or the right side. They are applied directly
against the tires. To engage, press the wheel-lock lever forward
against the stop (Fig.6.4.1). To release the wheel, pull the lever
back to the original position.
Braking power will decrease with:
• Worn tire tread
• Tire pressure that is too low
• Wet tires
• Improperly adjusted wheel locks.
The wheel locks have not been designed to be used as brakes
for a moving wheelchair. The wheel locks should therefore
never be used to brake a moving wheelchair. Always use the
handrims for braking. Make sure that the interval between the
tires and wheel locks complies with given specifications. To
readjust, loosen screws, (1), and set the appropriate interval,
(Fig.6.4.2). Tighten screw (see the page on torque).
Fig.
6.4.1
3 mm
1
Fig.6.4.2