background image

 

Programming Adapter Kit User’s Guide

  

QF4A512-PA

 

 

 

Rev A5, Feb 09 

www.quickfiltertech.com

 

Contact Information: 

 

 

Quickfilter Technologies, Inc. 
1024 S. Greenville Avenue, Suite 100 
Allen, TX  75002-3324 

 

 General: 

[email protected]

 

 Applications: 

[email protected]

 

 Sales: 

[email protected]

 

 Phone: 

214-547-0460 

 Fax: 

214-547-0481 

 Web: 

www.quickfiltertech.com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The contents of this document are provided in connection with Quickfilter Technologies, Inc. products. Quickfilter makes no representations or warranties with respect to the 
accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No 
license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in Quickfilter's Standard 
Terms and Conditions of Sale, Quickfilter assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, 
the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. 
Quickfilter's products are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other 
applications intended to support or sustain life, or in any other application in which the failure of Quickfilter's product could create a situation where personal injury, death, or 
severe property or environmental damage may occur. Quickfilter reserves the right to discontinue or make changes to its products at any time without notice. 

© 2008 Quickfilter Technologies, Inc. 

All rights reserved. 

 

Quickfilter, the Quickfilter logo and combinations thereof, are trademarks of Quickfilter Technologies, Inc. 

Other product names used in this publication are for identification purposes only and may be trademarks of their respective companies. 

 

Summary of Contents for QF4A512










Reviews: