background image

Estimated Altitude

Crumple up 

a piece of 

wadding and 

gently push 

down into 

space at top 

of Rocket 

Motor.

This line runs to 
tip of Capsule

What Else You Will Need

Prepping for Launch - Step01

Prepping for Launch - Step02

Prepping for Launch - Step03

MLAS

MLAS

FLYING YOUR MLAS ROCKET

FLYING YOUR MLAS ROCKET

Flying Model

Rocket Kit

A.

 Place 3 sheets of wadding inside the body tube. Set them so they are 

flat against the Black Mounting Ring.

B.

 Crumple up a piece of wadding and gently push down into space at 

top of Rocket Motor before inserting into rocket.

A.

 Grab the parachute at it's center and pull the shroud lines taut so that 

the parachute is in long narrow triangle shape.

B.

 Fold the parachute in thirds lengthwise, and DO NOT wrap the 

shroud lines around the parachute. See the illustration to the right for 
clarification.

TIP:

 

Lightly dust the parachute with Talcum or Baby Powder to keep it 

from sticking together. This works well in hot and humid or very cold 
weather.

A.

B.

A.

 Place the folded parachute for the Main Body Tube in first. Set it 

directly atop the Wadding inserted in Step 01A. Set the shock cord and 
shroud lines loosely atop the parachute.

B.

 Now place the two folded Capsule parachutes in the Main Body 

Tube. Set the shock cord and shroud lines loosely atop the parachutes.

C.

 Now insert the Capsule into the Main Body Tube, making sure that 

lines and cords do not get caught between the shoulder of the Capsule 
and the Body Tube, except the Capsule Parachute line, with must pass 
between the Capsule Shoulder and the Body Tube. 

To successfully fly your model rocket you will need the following items:

 Quest Launch Pad (No. 7610)
 Quest Launch Controller (No. 7510)

Rocket Motor 

 Estimated Altitude

B6-2 

 275 Feet

B6-4 

 300 Feet

 Quest Parachute Recovery Wadding (No. 7021)
 Quest Rocket Motor: B6-2, B6-4

PAGE10

READ AND FOLLOW THE ENCLOSED 

LAUNCHING PROCEDURES SHEET.

READ AND FOLLOW THE N.A.R. 

SAFETY CODE DURING ALL YOUR 

MODEL ROCKET ACTIVITIES.

Manufactured by:
Quest Aerospace, Inc.
PO Box 2409
Pagosa Springs, CO
81147
www.questaerospace.com

©2009-All Rights Reserved

Summary of Contents for Flying ModelRocket KitL











Reviews: