Quectel UG Series Command Manual Download Page 55

Page: 55 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 54 / 247

Parameter

UG95 module does not support this function.

4.3.14. AT+QCFG="remoteip" Enable/Disable Remote IP Function

AT+QCFG="remoteip"

is used to set the function whether or not “remoteip” negotiation will be injected

during the PPP dialing period. This parameter will not be saved and it will be effective immediately after

setting.

<enable>

0 Character escape function of SMS text is disabled

1 Character escape function of SMS text is enabled

When AT+CSCS=

“GSM” or AT+CSCS=“IRA”, in SMS text outputting:

0x5C (show in hex, character

in GSM, character \ in ASCII) will be

escaped into 0x5C3543

(“\5C”).

0x0D (show in hex, character <CR> in GSM and IRA) will be escaped into

0x5C3044

(“\0D”).

0x0A (show in hex, character <LF> in GSM and IRA) will be escaped into

0x5C3041

(“\0A”).

0x22 (show in hex, character “ in GSM and IRA) will be escaped into
0x5C3232 (“\22”).

0x00 (show in hex, character @ in GSM) will be escaped into 0x5C3030

(“\00”).

AT+QCFG="remoteip" Enable/Disable Remote IP Function

Write Command

AT+QCFG="remoteip"[,<remot

eIPsel>]

Response

If <remoteipsel> is absence which means read.

+QCFG: "remoteip",<remoteIPsel>

If none is absence which means setting parameters.

ERROR

If error is related to ME functionality:

+CME ERROR: <err>

Maximum Response Time

300ms

NOTE

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands