Quectel LG69T AM User Manual Download Page 6

Page: 6 / 46

GNSS Module Series

LG69T(AM,AS)_EVB_User_Guide 5 /

Contents

Safety Information ...................................................................................................................................... 3

About the Document .................................................................................................................................. 4

Contents ...................................................................................................................................................... 5

Table Index .................................................................................................................................................. 6

Figure Index ................................................................................................................................................ 7

Introduction ......................................................................................................................................... 8

General Overview ................................................................................................................................ 9

2.1.

EVB Kit ....................................................................................................................................... 9

2.2.

Connect Cables and Antenna to EVB ...................................................................................... 10

EVB Interfaces ................................................................................................................................... 12

3.1.

EVB Top View ........................................................................................................................... 12

3.2.

EVB Interfaces ......................................................................................................................... 13

Communication via QCOM Tool ...................................................................................................... 16

GNSS Module Firmware Upgrade via QGNSS Tool ...................................................................... 18

5.1.

QGNSS Setting ........................................................................................................................ 18

5.2.

QGNSS Interface Explanation ................................................................................................. 20

5.3.

Firmware Upgrade ................................................................................................................... 22

5.3.1.

Module’s MCU Firmware Download in Boot Download Mode...................................... 22

5.3.2.

Module’s MCU Firmware Upgrade in Normal Operating Mode .................................... 24

5.3.3.

GNSS Firmware Upgrade ............................................................................................. 27

EG25-G Module Firmware Upgrade via QFlash Tool .................................................................... 30

RTK Application ................................................................................................................................ 34

7.1.

Connect to Base Station .......................................................................................................... 34

7.1.1.

Hardware Connection ................................................................................................... 35

7.2.

Base Station Configuration ...................................................................................................... 36

7.2.1.

Base Station Receiver Mode Configuration .................................................................. 36

7.2.2.

Base Station RTCM MSM Mode Configuration ............................................................ 37

7.3.

RTK Data Interaction Mode Configuration ............................................................................... 37

7.4.

STRSVR Tool Configuration .................................................................................................... 38

7.4.1.

Steps for Data Transmission via NTRIP Protocol ......................................................... 38

7.4.2.

Steps for Data Transmission via TCP Protocol ............................................................. 40

Appendix Reference ......................................................................................................................... 43

Summary of Contents for LG69T AM















































Search results

Summary of Contents for LG69T AM

Reviews:

Related manuals for LG69T AM

Brands by name

Popular brands

Quectel LG69T AM, User Manual

Search results

Summary of Contents for LG69T AM

Reviews:

Related manuals for LG69T AM

Brands by name

Popular brands