Quectel LC79D (A) EVB User Manual Download Page 16 | Manualshive

Page: 16 / 23

background image

GNSS Module Series

LC79D (A) EVB User Guide

LC79D(A)_EVB_User_Guide 14 / 21

4

EVB Operation Procedures

This chapter mainly illustrates the operation procedures of LC79D (A) EVB.

4.1. Firmware Download

The module supports firmware download in both normal working mode and host mode.

4.1.1. Firmware Download in Normal Working Mode

Step 1:

Connect the EVB to a PC with a micro USB cable.

Step 2:

Turn on the POWER switch (S201) to power on the EVB.

Step 3:

Run the GNSSFlashTool and then configure the tool as shown below.

Figure 10: GNSSFlashTool Configurations for Firmware Upgrade



Please make sure the module is in full on mode before downloading firmware in normal working mode.

NOTE

«
...
14
15
16
17
18
...
»

Summary of Contents for LC79D (A) EVB
























Reviews:

No comments

Related manuals for LC79D (A) EVB

Brand: Ebyte Pages: 31

Brand: Vanderbilt Pages: 6

E70-433T S Series

Brand: Ebyte Pages: 37

Brand: SIM Tech Pages: 61

eBlocks EB066-00-2

Brand: Matrix Pages: 8

Brand: Interlogix Pages: 44

Brand: Fibocom Pages: 43

Brand: Fibocom Pages: 49

Brand: Fibocom Pages: 78

Brand: Fibocom Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands