Quectel LC79D (A) EVB User Manual Download Page 10 | Manualshive

Page: 10 / 23

background image

GNSS Module Series

LC79D (A) EVB User Guide

LC79D(A)_EVB_User_Guide 8 / 21

Table 2: List of Accessories

2.3. EVB and Accessories Assembly

The following figure shows the assembly of LC79D (A) EVB and its accessories.

Figure 3: LC79D (A) EVB and Accessories Assembly

Items

Description

Quantity

USB Cable

Micro USB Cable

1

EVB

LC79D (A) evaluation board

1

Antenna

GNSS antenna (Active)

1

USB Flash Drive

USB Flash Drive (including LC79D related

documents, tools, drivers, etc.)

1

Instruction Sheet

A sheet of paper giving instructions for EVB

connection, details of EVB accessories, etc.

1

Other

Bolts and coupling nuts

4 for each

«
...
8
9
10
11
12
...
»

Summary of Contents for LC79D (A) EVB
























Reviews:

No comments

Related manuals for LC79D (A) EVB

Brand: Ebyte Pages: 14

Brand: Ebyte Pages: 11

Brand: Ebyte Pages: 13

Brand: Ebyte Pages: 21

Brand: Vanderbilt Pages: 6

Brand: Ebyte Pages: 21

Brand: Silex technology Pages: 8

Brand: FALCOM Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands