manualshive.com logo in svg

Quatech SATA2PX-100, User Manual

Share
Download
Quatech SATA2PX-100 User Manual Download Page 12

May/07

                                                                         

MN

         

 

 

 

12

6.

 

Insert the floppy disk, then press 

Enter

. 

7.

 

Select 

Silicon Image SiI 3132 SoftRaid 5 Controller for 

Windows XP/Server 2003

, then press 

Enter

. 

8.

 

Press 

Enter 

to finish driver installation, then follow the on-screen 

instructions to complete the Windows installation. 

Note: 

If the 

Security Alert 

warning pops up, click 

Yes

. Our driver has 

passed Microsoft compatibility testing, this message appears during 

new installation. 

 

 

For An Existing Installation 

1.

 

Setup the RAID Array prior to driver installation and boot up to 

Windows. 

2.

 

At the 

Found New Hardware Wizard:

 

    XP(w/SP1 or earlier)/Server 2003: continue to step #3 

XP(w/SP2 or later)/Server 2003(w/SP1 or later): select 

No, not 

this time

, then click 

Next

. 

3.

 

Insert the driver CD, select 

Install the software automatically 

(Recommended)

, and click 

Next

. 

4.

 

Accept the default entry, then click 

Next

. 

Summary of Contents for SATA2PX-100

















Reviews:

No comments

Brands by name

Popular brands

Load more brands