manualshive.com logo in svg

Quatech SATA2PX-100, User Manual

Share
Download
Quatech SATA2PX-100 User Manual Download Page 11

May/07

                                                                         

MN

         

 

 

 

11

BIOS Configuration 

The SATA2PX-100 BIOS will appear every time your system starts up. 

If the BIOS doesn’t show up, please try your controller in another 

ExpressCard slot. During this (POST) process, the BIOS will show up 

and indicate the devices attached to it.

 

 

Driver Installation 

For Windows® XP/Server 2003 

For New Operating System Installations 

A new installation requires a floppy disk for the driver 

installation. To make this floppy disk, copy the contents of 

the “

ExpressCard\SATA2PX-100\RAID\FLOPPY” folder, found on 

the driver CD, onto a blank floppy disk then follow the directions 

below.

 

1.

 

Setup the RAID Array prior to Windows installation. 

2.

 

Follow Microsoft’s Windows installation procedure. 

3.

 

Restart the computer when prompted by Windows’ installation. 

4.

 

At the Windows Setup screen, press 

F6

 to install the RAID driver. 

5.

 

When prompted, press 

S 

to specify the location of the driver. 

Summary of Contents for SATA2PX-100

















Reviews:

No comments

Brands by name

Popular brands

Load more brands