manualshive.com logo in svg

Quark-Elec Seatalk QK-A033, Manual

Share
Download
Quark-Elec Seatalk QK-A033 Manual Download Page 2

Quark-elec Manual

https://www.quark-elec.com

2 of 21

2019

V1.0

Contents

1. Introduction

.....................................................................................................................................................

3

2. Mounting

.........................................................................................................................................................

4

3. Connections

...................................................................................................................................................

5

3.1.

SeaTalk

1

.............................................................................................................................................

6

3.2.

NMEA Inputs and Outputs

...............................................................................................................

7

3.2.1.

MNEA Inputs

......................................................................................................................

7

3.2.2.

MNEA Outputs

...................................................................................................................

7

3.2.3.

Addition Functions

............................................................................................................

7

4. Wireless Connections

...................................................................................................................................

9

4.1.

WiFi Ad-hoc mode

............................................................................................................................

9

5. Connecting via USB port

............................................................................................................................

10

5.1.

Will a driver needed to connect via USB?

..................................................................................

10

5.2.

Bi-directional USB

..........................................................................................................................

10

5.3.

Checking the USB connection (Windows)

..................................................................................

10

6. Status LED’s

................................................................................................................................................

11

7. Configuration

................................................................................................................................................

12

7.1.

Configuring Baud Rates

................................................................................................................

13

7.2.

WiFi - Station mode

........................................................................................................................

14

7.3.

WiFi - Standby

.................................................................................................................................

14

7.4.

Configuring Routing and Filtering

................................................................................................

15

7.4.1.

Filtering: Black list setup

.................................................................................................

15

7.4.2.

Routing data away from chosen outputs

........................................................................

15

7.5.

USB Configuration: Monitoring and Sending NMEA Messages

.............................................

16

7.6.

USB communication with Autopilots

............................................................................................

16

8. Upgrading firmware

.....................................................................................................................................

17

9. Chart software

.............................................................................................................................................

18

9.1.

OpenCPN example USB setup

....................................................................................................

18

9.2.

OpenCPN example Network setup

..............................................................................................

19

9.3.

Maps

.................................................................................................................................................

19

10.

Specification

.............................................................................................................................................

20

11.

Limited Warranty and Notices

...............................................................................................................

21

12.

Glossary

...................................................................................................................................................

21

Summary of Contents for Seatalk QK-A033






















Reviews:

No comments

Brands by name

Popular brands

Load more brands