manualshive.com logo in svg

Quark-Elec Seatalk QK-A033, Manual

Share
Download
Quark-Elec Seatalk QK-A033 Manual Download Page 13

Quark-elec Manual

https://www.quark-elec.com

13 of 21

2019

V1.0

7.1. Configuring Baud Rates

NMEA 0183 input and output baud rates can be setup from dropdown menu. A033 can work with the

standard NMEA 0183 devices (4800bps) or the high-speed NMEA 0183 devices (38400bps), 9600bps

can also be chosen.

NMEA baud rates are set to the following default settings:

NMEA IN 1: 4800bps

NMEA IN 2: 4800bps

NMEA IN 3: 38400bps

NMEA OUT 1: 4800bps

NMEA OUT 2: 38400bps

These can be adjusted as required.

Figure 9 Setup the baun rate

When A033 is connected to a computer (Windows system) and powered up, ‘A033 connected’ will be

shown at the centre of the bottom and the software version shows at the bottom right. Press ‘

Config

’

once you have set the Baud rates for the inputs and outputs to save them to the A033.

Then press the ‘

Disconnect’

button to safely remove the device from the PC.

Re-start the A033 to active the new settings to the device.

Summary of Contents for Seatalk QK-A033






















Reviews:

No comments

Brands by name

Popular brands

Load more brands