Quark-Elec QK-AS07-0183 Manual Download Page 9

 
 

QK-AS07-0183 Manual 

 

V 1.0 

9 of 10 

2020 

 

 

5.  Data Output Protocols 

AS07-0183 support the following output NMEA sentences: 
 
$xxGGA - GPS Fix Data 
$xxGLL - Geographic Position Latitude and Longitude 
$xxGSA - GNSS DOP and Active Satellites 
$xxGSV - GNSS Satellites in View 
$xxRMC - Recommended Minimum Specific GNSS Data 
$xxVTG - Course Over Ground and Ground Speed 
$xxZDA - Time and Date 
 
‘xx’ above represents ‘GP’ if GPS, ‘GL’ if GLONASS and ‘GA’ if GALILEO 

6.  Specification 

Item 

Specification 

Operating temperature 

-5°C to +80°C  

Storage temperature 

-25°C to +85°C  

AS07-0183 Power supply 

12-24 VDC 

AS07-0183  supply current 

≤40mA 

GPS Satellites Tracked 

14-channel (maximum) 

GPS Satellites Acquired 

51-channel (maximum) 

WAAS/EGNOS Satellites Tracked 

Any available channel 

GPS Position Accuracy 

3m (10’) with WAAS (95% of the time, SA off) 

GPS-Fix Update Rate 

Up to 10 times per second (user selectable) 

Cold Start Acquisition 

60 seconds 

NMEA data format 

NMEA 0183 

Certifications and Standards 

CE, IPX6, RoHS 

   

7.  Limited Warranty and Notices 

Quark-elec warrants this product to be free from defects in materials and manufacture for two years from 
the date of purchase. Quark-elec will, at its sole option, repair or replace any components that fail in 
normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour. 
The customer is, however, responsible for any transportation costs incurred in returning the unit to 
Quark-Elec. This warranty does not cover failures due to abuse, misuse, accident or unauthorized 
alteration or repairs. A returns number must be given before any unit is sent back for repair. 
 
The above does not affect the statutory rights of the consumer. 

 

8.  Disclaimer 

This product is designed to aid navigation and should be used to augment normal navigational 
procedures and practices. It is the user’s responsibility to use this product prudently. Neither Quark-elec, 
nor their distributors or dealers accept responsibility or liability either to the products user or their estate 
for any accident, loss, injury or damage whatsoever arising out of the use or of liability to use this 
product. 
 
Quark- products may be upgraded from time to time and future versions may therefore not correspond 
exactly with this manual. The manufacturer of this product disclaims any liability for consequences 
arising from omissions or inaccuracies in this manual and any other documentation provided with this 
product. 
 

Summary of Contents for QK-AS07-0183











Reviews: