manualshive.com logo in svg

Quantum ATL StackLink, Installation Instructions Manual, Page: 15 / 28

Share
Download
Quantum ATL StackLink Installation Instructions Manual Download Page 15

Quantum|ATL StackLink™ Installation Instructions

Document 6421009-03, Ver. 3, Rel. 0

November 2001

Attaching the Shuttle Assembly to the Top and Bottom Mounting Tray Assemblies

15

Attaching the Shuttle Assembly to the Top and Bottom 

Mounting Tray Assemblies

0

To attach the shuttle assembly to the top and bottom mounting tray 

assemblies:

1

At the rear of the rack, lift the shuttle assembly and position it so 

the carriage faces forward into the rack.

2

Rest the lower end of the shuttle assembly on top of the bottom 

mounting tray assembly.

3

Ensure that the motor at the top of the shuttle assembly is aligned 

with the cutout in the top mounting tray assembly.

4

Slide the shuttle assembly fully into the rack.

5

Secure the shuttle assembly to the upper and lower mounting trays 

using six screws (YS40097) and washers (YS40402) provided in the 

StackLink kit (see 

figure 13

).

Figure 13  Installing the 
Shuttle Assembly

Note:

Tighten these screw to finger-tightness only. You will 

finish securing the StackLink after you have installed 

libraries in the rack.

(SHOWN OUTSIDE OF RACK)

FRONT

REAR

Summary of Contents for ATL StackLink





























Reviews:

No comments