background image

8

CLEANING

To clean unit first turn off controls on unit and unplug the unit from 

power source. To clean glass display panel; remove dust with clean 

dry cloth or to remove finger prints and other marks clean glass with 

clean damp cloth. Do not use abrasive cleaners or spray liquids on 

glass display panel surface. Metal and metal painted parts should 

be cleaned with damp cloth. Do not use abrasive cleaners or spray 

liquids on these surfaces. 

WARRANTY

Every electric fireplace heater is tested before it leaves the factory 

and it is guaranteed for one year. If the unit should fail to operate 

correctly within one year from the date of purchase, call customer 

service at 1-800-459-4409 (EST). We will, at our discretion either 

repair or replace the unit. It will have to be returned to us freight 

prepaid and we will return the repaired or replaced unit to you 

freight prepaid. The company’s sole obligation is to repair or replace 

the unit. 

This warranty is void if in the opinion of Quality Craft the unit has 

been tampered with, altered, misused, damaged, abused or used 

with the wrong power source. Light bulbs are not covered by this 

warranty. The warranty is for homeowner use only and does not 

cover units used in commercial situations.

Imported by  

quality Craft

Laval, Quebec, Canada  H7S 2G7 

1-800-459-4409 (EST) 

www.qualitycraft.com        

Made in China

Summary of Contents for MM480PG-47CW









Reviews: