Qualcut RA0038LS Operating Instructions Manual Download Page 14

14.

POWER PRODUCTS LLC.

Fig 6.

Mark for usable limit on cover.

Slit on eyelet part.

Fig 7.

IMPORTANT! The latches fully spread 

in the windows. (Shaded area)

• 

Ensure chain is kept well sharpened and replaced when  

worn.

• 

Replace guide bar and chain drive sprocket when worn.

• 

Use only designated, fresh chain bar lubricant in the bar 

lubricating system.

• 

Check and adjust chain tension every hour of operation 

and following first 10 minutes of operation with a new 

chain.

• 

Do not allow the chain to come in contact with any other 

object other than wood while performing a cut, as this will 

blunt/ damage the chain immediately.

•  Ensure blades are kept sharp and covered when not in 

use.

•  Ensure gearbox and blades are regularly lubricated with 

quality lithium based grease.

•  Check and adjust correct blade clearance regularly.

Storing the product differs depending on the amount of time 

it will be in storage.

Follow these steps to store the product short term:
1.   Clean all foreign material from the product.
2.   Store in a well-ventilated place that is inaccessible to 

children.

If you do not intend to use the product for more than one 

month, follow these steps to store the product long term:

1.   Drain all fuel from tank into a container approved for 

petrol.

2.   Run the engine until it stops.
3.   Clean all foreign materials from the product.
4.   Remove the spark plug boot, and then the sparkplug.
5.   Pour approximately 5ml oil into the cylinder through the 

sparkplug hole.

6.   Pull the recoil starter 2 or 3 times to distribute the oil over 

the cylinder walls.

7.  Leave engine oil in at this stage, However complete an 

engine oil change when you come to use the RA0038LS 

again.

STORING YOUR MULTI-TOOL

8.   Reinstall the spark plug. Follow the instructions for 

sparkplug replacement.

9.   Reconnect the spark plug boot.
10. Store the product in a well-ventilated place that is 

inaccessible to children.

CAUTION: Keep the product away from corrosive agents 

such as garden chemicals.

IMPORTANT: Abide by all federal and local regulations for 

the safe storage, handling and disposal of petrol. Never 

store this product with any fuel remaining in the tank, fuel 

lines or carburettor. Your warranty does not include 

coverage for damage covered by stale or contaminated 

fuels.

THE CHAINSAW PRUNING 

ATTACHMENT

THE HEDGE TRIMMER 

ATTACHMENT

Summary of Contents for RA0038LS





















Reviews: