background image

  

  

15

14

  

  

Customer Helpline 

0845 034 2279

www.gardenservicecentre.co.uk

Customer Helpline 

0845 034 2279

www.gardenservicecentre.co.uk

Maintenance 

Store

– Never store the equipment with gas in the tank, inside a building where fumes can reach an open 

flame or spark.

– Allow the engine to cool before storing in any enclosure.

– To reduce the fire hazard, keep the storage area clean.

– If the fuel tank has to be drained, this should be done outdoor.

Troubleshooting

General Troubleshooting

CAUTION!

 Danger of injury! Improperly conducted repairs may prevent your device from working 

safely. Such repairs will endanger you and your surroundings.

Minor faults are often sufficient to cause a malfunction. In most cases, you will be able to correct 

these faults easily. Please start by referring to the following table before contacting our technical 

support. This will help you save much effort and possibly expense.

Fault/malfunction

Possible Cause

Solution

Engine will not start

Is the tank empty?

Filling with fuel

Is the throttle set to        ?

Set the throttle to         .

Ignition cable plug not firmly 

attached?

Push the plug on tightly.

Is the ignition cable plug dirty?

Clean the plug.

Is there excess fuel inside the 

combustion chamber?

Remove the spark plug, dry off 

the electrode, and start at full 

throttle.

Spark plug dirty?

Clean the spark plug.

The distance between the 

electrodes of the spark plug is too 

large.

Set the gap to 0.7 to 0.8 mm.

Wrong fuel?

Drain the tank and fill it with the 

correct fuel.

Spark plug defective?

Replace the spark plug.

Engine will not reach its 

maximum speed

Air filter dirty?

Cleaning the air filter.

Spark plug dirty?

Clean the spark plug.

Is the electrode separation of the 

spark plug too large?

Set the gap to 0.7 to 0.8 mm.

Wrong fuel?

Drain the tank and fill with the 

correct fuel .

Clutch does not release

Incorrect clutch setting?

Adjusting the clutch.

Summary of Contents for HST-1003A















Reviews: