background image

The Trusted Source

®

2

READ ALL SAFETY MESSAGES AND ALWAYS WEAR
SAFETY GLASSES WHEN WORKING WITH TOOLS.

a hazardous situation which, if not avoided, could result in death or
serious  injury.  You  CAN  be  KILLED  or  SERIOUSLY  HURT  if  you  don’t
follow instructions.

a  hazardous  situation  which,  if  not  avoided,  could  result  in  minor  or
moderate  injury.  You  CAN  be  moderately  HURT  and  also  may  suffer
property damage if you don’t follow instructions. 

Careful attention is required to this instruction or operation but does
generally  not  relate  to  personal  injury.  Damage  to  your  Quadratec

®

product or other property may result if you don’t follow instructions. 

A Few Words About Product Safety: 

Your Quadratec

®

Aluminum Front

Bumper is intended to enhance the util-
ity and enjoyment of your off road capa-
ble vehicle. Before installation, please
review the following safety information
and installation recommendations.

Throughout these instructions impor-
tant safety information is generally
preceded by one of three signal words
indicating the relative risk of injury,
property damage or adverse conse-
quence. 

The signal words mean:

Before You Begin Installation: 

Congratulations on your purchase of
Quadratec

®

Aluminum Front Bumper for

your Jeep

®  

Wrangler. This custom fit

front Bumper has been designed for
long life and a great look. Though con-
structed of only the finest materials, this
bumper must be maintained to keep its
look while performing under the tough-
est conditions. Please see page 10 for im-
portant care & maintenance tips to keep 

your bumper looking like new. When
unpacking, check to make sure all parts
are included and not damaged due to
shipping. If any part is missing or
broken, please call Customer Service
at 800-745-6037 as soon as possible.

Thank you again for your purchase and
let’s start the installation process.

AS YOU UNPACK YOUR FRONT BUMPER, BE CAREFUL NOT TO
SCRATCH THE FINISH WITH A KNIFE OR RAZOR. WE SUGGEST
PLACING THE UNPACKED BUMPER BACK INTO THE ORIGINAL BOX
SO IT DOES NOT GET SCRATCHED BEFORE THE INSTALLATION BEGINS.
THIS BUMPER HAS A CUT-OUT FOR A VEHICLE RECOVERY WINCH.
THE BUMPER FEATURES AN INTEGRATED WINCH MOUNTING PLATE.

WELDED FRONT BUMPERS ARE HEAVY AND WE STRONGLY SUGGEST
THE ASSISTANCE OF AN ABLE-BODIED ASSISTANT DURING LIFTING
AND INSTALLATION OF YOUR BUMPER.

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4  6/25/19  1:45 PM  Page 2

Summary of Contents for 12057.0261













Reviews: