background image

The Trusted Source

®

2

Before You Begin Installation: 

Congratulations on your purchase of
Quadratec Rock Crawler Front Bumper
for your Jeep

®  

Wrangler. This custom fit

front Bumper has been designed for
long life and a great look. Though con-
structed of only the finest materials, this
Tube Bumper must be maintained to
keep its look while performing under the
toughest conditions. Please see page 5
for important care and maintenance tips 
to keep your bumper looking like new.

When unpacking, check to make sure all
parts are included and not damaged due
to shipping. If any part is missing or
broken, please call Quadratec Customer
Service at 800-745-6037 as soon as pos-
sible.

Thank you again for your purchase and
let’s start the installation process.

A Few Words About Product Safety: 

Your Rock Crawler Front Bumper is in-
tended to enhance the utility and enjoy-
ment of your off road capable vehicle.
Before installation, take a moment to
review the following safety information 

and installation instructions. Important
safety information is generally preceded
by one of three signal words indicating
the relative risk of injury.  
The signal words mean:

Bumper Spacer Plates
(part of the QRC Bumper kit)

Optional Winch
Mounting Plate #92122.2900

As you unpack your front bumper, be careful not to scratch the finish
with a knife or razor. We suggest placing the unpacked bumper back
into the original box so it does not get scratched before the installa-
tion begins. This bumper has a cut-out for a vehicle recovery winch.
A separate Winch Mounting Plate is required for installation. If you
do not have this winch plate, go to quadratec.com and order part
#92122.2900. The instructions below call out in step number two
when this winch plate will need to be installed.

a hazardous situation which, if not avoided, could result in death or
serious injury. You CAN be KILLED or SERIOUSLY HURT if you don’t
follow instructions.

a hazardous situation which, if not avoided, could result in minor or
moderate injury. You CAN be moderately HURT and also may suffer
property damage if you don’t follow instructions. 

Careful attention is required to this instruction or operation but does
generally not relate to personal injury. Damage to your Quadratec

®

product or other property may result if you don’t follow instructions. 

QRC_F_Tube_12057_0102_LTR.qxp_Layout 1  5/16/16  4:21 PM  Page 2

05162016162436

Summary of Contents for 12057.0102









Reviews: