background image

Page  12

7037-135E

September 1, 2008

R

4300 Wood Stove Series (ACC)

A.  Hearth Protection Requirements

FLOOR PROTECTION:  

Floor protector must be non-com

-

bustible material, extending beneath heater and to the front, 

sides and rear as indicated.  The floor must be non-com

-

bustible or otherwise adequately protected from radiant heat 

given off by the unit and from sparks and falling embers.  A 

layer of thin brick or ceramic tile over a combustible floor is 

not sufficient. 

For US installations,

 it is necessary to install a floor protector 

of a minimum of /8 inch (9.5mm) thick metal clad millboard 

or equivalent a minimum of 16 inches (406mm) in front of 

glass  and 8 inches (20mm) to both sides of the fuel loading 

door.  Open the door and measure 8 inches  (20mm) from 

the side edge of the opening in the face of the appliance. 

*

See exception. 

16" from glass 

8 in. 

Fuel loading door 

4-7/8 in. 

3-1/8 in." 

31-5/8 in. 

minimum

41-3/8 in.

minimum

1

-5/8

 in

.

27

-/8

 in

.

7 in.

40

-15

/16

 in

.

-1

/16

 in

.

135°

op

tio

na

l

co

ve

rag

e

51-1/16 in.

Must extend 2 in. (51mm) beyond

each side of pipe (shaded area)

20mm (8 in.)

20mm

(8 in.)

20mm

(8 in.)

457mm (18 in.)

105mm

(51-/8 in.)

minimum

1041mm (41 in.)

minimum

In  Canada,

  similar  floor  protection  must  be  provided  18 

inches (457mm) in front and 8 inches (20mm) from the 

sides and rear of the stove.  *

See exception.

*ExCEPTION:

    Non-combustible  floor  protections  must 

extend beneath the flue pipe when installed with horizontal 

venting  and  extend  2  inches  (51mm)  beyond  each  side. 

See Figure 12.4.

USA required

Canada recommended

Figure 12.3

4

Installation

Figure 12.1

Figure 12.2

Figure 12.4

WARNING

Fire Risk.

•  Hearth pads must be installed exactly as 

specified.

High temperatures or hot embers may ignite 

concealed combustibles.

Millennium Model

USA

USA

CANADA

Summary of Contents for Quadra-Fire 43M-ACC-MBK

















































Reviews: